Patch Hollow Core Wood Door

Repair a Hole in an Oak Tongue and Groove Floor and Finish the Patch to Match in Color and Gloss.

You can repair a hole if you re willing to paint the door to hide the patch. To do this, you ll need a can of spray foam insulation. In many cases, you can repair.

How to Add a Glass Window to a Hollow Core Door More. Hollow Core Door Makeover Diy, Glasses, Hollow.

I don t usually post, but had to after seeing this. What a joke. Most panel hollow core doors have a wood grain look. You will end up with a flat spot on your door.

Time and age cause doors to bind and stick. As your house settles, doors sag in their frames; in addition, repeated painting and dirt create buildup. Or, a door may have been misaligned from the start. A variety of problems occur with doors. Some, such as damage to their surfaces, can happen to any type of doors. Other problems are unique to the way a door operates. Pocket doors can jump their tracks, bi-fold doors can pop out of their pivot mounts, and hinged doors can become stuck in their frames.

In this article, we ll help you repair all of these types of interior door problems, beginning with hinged doors, which can become balky, sticking in their frame, they can become too loose to seal properly, or their surfaces can become damaged.

Please note that many problems that occur with exterior entry doors, such as a front door, are the same as those that happen to interior doors.

Mark the door with a light pencil line where it binds against the jamb.

Fixing a Door That Binds

If a door binds or rubs against the jamb, identify the spots where it binds by sliding a thin strip of cardboard or wood between the door and the jambs. Then mark the areas where the door is binding with a pencil. Look for a buildup of paint, which usually is the culprit. Hold a sharp wood chisel flat against the surface, and slice off the excess. Then smooth the surface with fine-grit sandpaper. Coat the door edges and the jambs with paraffin.

If that doesn t do the trick, try adjusting the hinges. Many doors bind against the upper corner of the jamb or drag across the carpet. Close the door, and check how it fits in the jamb. Look for tight spots, and make sure the top edge of the door is level. If it appears to be more than 1/4 inch out of level, the cause is probably settling or sagging.

You can usually solve this by replacing the center screw of the upper hinge with a longer, 2 1/2-inch screw, angled slightly toward the jamb s center. First, clean off any dirt, and repair or replace any bent hinges. Drive the screw in snugly, and tighten the other screws that secure the hinge. If they can t be tightened, repair the screw holes by packing them with short pieces of a glue-coated dowel. Then replace the screws.

Another culprit in a door that binds is humidity, which can cause a door to swell and stick. To fix this, you will probably have to remove the door and sand or plane down the high spots. Before removing the door and planing it, first try sanding the areas with coarse, followed by finer, sandpaper.

Plane the edge of the door, working from the corner toward the center.

To plane the door, you ll need to remove it. For instructions on removing a door, see How to Remove a Door.

How to Plane a Door

Using a pencil, mark the area to be planed on both faces of the door. Typically, you should be able to slide a dime between the door and the jamb along both sides and the top.

Set the door on edge, and, using a jack plane with a sharp blade set to make a very shallow cut, plane in line with the wood grain to avoid gouging the wood. Plane the top or bottom rail or hinge stile if that s where the door binds. Avoid planing the lock stile not only is the lock side usually beveled to allow for a tight fit, but planing it can also compromise the way the lock set fits. Hold the plane at a slight angle and flat against the surface. At the door s top and bottom, plane from the corner toward the middle to avoid splitting the ends of the stiles.

Don t take too much off remember, the door will shrink back up when the air is drier. Finish by coating the door edges and jambs with paraffin.

Fixing a Loose Door

If door rattles, adjust the position of the strike plate.

This is generally the opposite of sticking in the jamb. When an interior door rattles, this means the door stop and/or the strike plate are not tight enough. If the strike plate has a flange in the center that can be bent slightly to tighten the fit, remove the plate and use a pair of pliers to bend the flange. Otherwise, you may have to adjust the position of the door stop on the latch-side jamb.

To do this, first use a utility knife to cut the paint seal between the molding and the jamb. Then place a wooden block against the door stop, and hammer the block gently toward the door to provide a tighter fit.

The best way to stop an exterior door from rattling is to install resilient weatherstripping around its perimeter, which also will help insulate your house. Look for the vinyl bulb type and follow package instructions.

Hole In A Hollow-Core Door

If you have a hollow-core door with a serious hole in it, consider replacing the entire door; hollow-core doors are modestly priced.

Hole in a hollow-core door can be filled and smoothed; then the door must be painted.

You can repair a hole if you re willing to paint the door to hide the patch. To do this, you ll need a can of spray foam insulation. In many cases, you can repair the door without removing it first just spread a dropcloth on the floor beneath it before you start.

1Fill the hole with the spray foam insulation, allowing the foam to expand slightly above the door s surface.

2Let it dry and continue to expand overnight.

3Use a razor blade to slice off the excess. Shave the mound just slightly lower than the door s surface.

4Apply vinyl spackling compound to the patch, using a 3-inch putty knife. Draw it smooth to the door s surface. Allow the spackling compound to dry.

5Sand the area lightly with fine sandpaper wrapped around a sanding block.

6Prime the entire surface of the door, allow it to dry, and then paint.

Fixing Wood Door Problems

There are many methods for repairing or restoring woodwork, and they work just as well on wood doors.

You can sand out minor scratches, fill gouges with wood putty, replace rotted or broken sections with epoxy filler or by gluing in a new piece, and so on.

If a panel in a Colonial-style door is cracked or split, you may be able to reglue it without removing it from the rest of the door.

If you have to remove a panel or replace it completely, try prying off the moldings that surround it and hold it in place. On some panel doors the moldings are routed in and can t be removed. In this case, one option is to cut away these integral moldings carefully. After you ve fixed the panel, buy new moldings to match the rest of the door s trim.

More Door Repairs

For step-by-step methods of fixing interior pocket doors and bifold doors, next please see:

Pocket Door Repairs

Bifold Door Repairs

You ll find the following fixes in the exterior door section of HomeTips.

Mar 12, 2009  Easy DIY repair of hole in hollow core door. Looks like new.

Hollow core doors are commonly used in residential construction. Although they are not made of solid wood like exterior doors, hollow core units are not truly hollow.

How to Fix an Interior Door

Oct 20, 2012  TRW - The Real World - DIY yourself shows how to simplify an otherwise, somewhat complicated repair when your hollow core door shows why it s a H/C door.

The skin on a hollow-core luan door is rarely thicker than 1/4 inch, and it s all too susceptible to breakage. When it does break, it s not too expensive to replace.

A hole in a garage door allows airborne contaminants to enter the garage and so it must be closed. You can patch a hole in your garage door without having to call in.