Xp Usb Ehci Driver
How to obtain and to install USB 2.0 drivers in Windows XP Service Pack 1
Article ID: 329632
This article was previously published under Q329632
The third-party products that this article discusses are manufactured by
companies that are independent of Microsoft. Microsoft makes no warranty,
implied or otherwise, regarding the performance or reliability of these
products.
Drivers; Input Devices; Intel USB 3.0 Driver 3.0.5.69. You can download the Intel USB 3.0 driver for Windows 7 right here. If you need this driver for Windows XP.
Tools
For SuperSpeed USB software and hardware tools, please click here. USB20CV R1.4.16.1. The installation utility, InstallUSB20CV14161.msi 12.6MB contains USB.
Full article here. What is this about. To keep the introduction short, Microsoft denies that booting Windows off a USB drive works. See this page for example.
For SuperSpeed USB software and hardware tools, please click here.
USB20CV R1.4.16.1
The installation utility, InstallUSB20CV14161.msi 12.6MB contains USB Command Verifier USB20CV version R1.4.16.0
and documentation. USB20CV is the compliance test tool which evaluates
High, Full and Low-speed USB devices for conformance to the USB Device
Framework Chapter 9, Hub device class Chapter 11, HID class, and OTG
specifications. Also included are mass storage class and USB video
class specification tests. All USB peripherals are required to pass the
Device Framework tests in order to gain certification. The other tests
are mandatory for certification when supported. If you have
installed a previous version of the USB 2.0 Command Verifier, you must
uninstall it before installing the new version
USB20CV revision 1.4.16.1
is the official test tool for device framework testing. As of April
2007, the mass storage class tests and the video class tests are
official and mandatory. This software is provided courtesy of Intel
Corporation.
The USB20CV x64Bit revision 1.4.16.1 can be downloaded here.
NOTE: For this workshop we we will use version 1.4.16.x. Any software update is a bug fix.
The USB20CV tool is supported on Windows 7 and above only.
NOTE: Please do not install this tool on a machine that already has previous versions of USB20CV installed.
This software release will work on Windows 7 with User Access Control
disabled or Windows 8 with User Access Control disabled. This tool
requires an Enhanced Host Controller Interface, EHCI. If testing Full
or Low-speed devices, an intervening Hi-Speed USB Hub is required.
USB20CV R1.4.16.1 uses a special purpose driver for the Hi-Speed USB Host Controller. USB20CV R1.4.16.1 automatically replaces the standard Microsoft EHCI host driver with its own test stack driver. When USB20CV R1.4.16.1 exits, the original standard Microsoft EHCI host driver is restored.
Stack switching has been extensively tested with Microsoft EHCI drivers
only. Stack switching has not been tested with USB 2.0 host controller
drivers provided by other vendors. Please read the Release Notes for
details.
USB Electrical Analysis Tool 2.0, version 1.20 for Windows
USBET20 8MB, April 2013
is a stand-alone electrical signal analysis tool for USB Compliance
testing. USBET20 is the official compliance electrical analysis tool
that performs pass/fail assessments on signal quality and inrush current
data captured from an oscilloscope.
NOTE:
Some of the approved oscilloscope test solutions use proprietary
software to assess signal quality and inrush current events. The only
official analysis tool for certifying signal quality and inrush current
is USBET20 published by the USB-IF. Please be sure to run captured
signal quality and inrush current test data through USBET20 for an
official assessment of the measurement.
USBET20 accepts. tsv and. csv data files generated by USB-IF approved digital oscilloscopes and produces the familiar. html results files of the analysis.
USBHSET version 1.3.0.2 for EHCI
This tool kit contains the Window-based HSET
utility used to initiate test modes. Detailed test procedures for
high-speed host, hub and device electrical testing, tailored to common
test equipment, can be downloaded here. A
USB Electrical Analaysis Tool is available separately for download see
USBET above. The procedures for legacy testing can be found in the USB-IF Compliance Program area. This software provided courtesy of Intel Corporation.
NOTE: The USBHSET tool works on Windows 7 and above only. Email admin usb.org if you would like an old version of the tool that supports XP.
EHSETT 32-bit versionEHSETT 64-bit version
HSET Documentation version 0.41 for EHCI and xHCIUSBHTT 1.2 Release - Windows 2000 and Windows XP only
The installation utility, USBHTT.msi 11
MB, contains the USB2 Hub Transaction Translator Test Suite. USBHTT
is a compliance test tool which evaluates Hi-Speed USB Hubs for
conformance to the USB Hub device class Chapter 11. USBHTT suite
focuses on protocol evaluation of the transaction translator unit in
high-speed hubs. The 1.2 release is a requirement for Hi-Speed USB Hub
silicon certification. It is not required for end product hub
certification. This version of USBHTT was posted on 7/07/2003. This
software release will only work on Windows 2000 and Windows XP. Please
check the release notes and accompanying documentations for details on
using USBHTT and how to provide the USB-IF feedback on issues and
suggestions. Some of the USBHTT tests require custom test devices. These
devices may be ordered from the USB-IF eStore page USBHTT version 1.2 is a maintenance
release that fixes test issues, improves logging features, and removes
some tests from required sequences. As one part of Hi-Speed USB Hub silicon certification process, Hub Silicon Manufacturers use the USB-IF USBHTT Manufacturer Self-Testing Program to complete USBHTT test requirements.
USB PD Vendor Info File Generator Version 0.9.12.0 Updated December 15, 2015 can be downloaded here.
Company List
Please download the Company List and
save as usb.if in the same directory where USBCV was installed. Please
check the installation instructions for USBCV for details. Remember this
list changes almost daily, be sure to get a fresh copy when you use the
tools.
Invalid VIDs
The VIDs included on this list have been obsoleted and are not valid.
Compliance Updates
Please review the USB-IF Compliance Updates webpage frequently and subscribe to the news feed for the latest information regarding the USB-IF Compliance Program.
Jun 20, 2014 Describes an issue in Windows XP SP1 where USB 1.1 devices that are attached to an EHCI USB 2.0 host controller may stop functioning if you try to update.
USB3CV Tool. The USB3CV tool Ver. 2.0.3.0 December 21, 2015 is available here. Download USB3CV.msi for 32-bit Windows or USB3CV_x64.msi for 64-bit Windows.
USB 2.0 support for any Enhanced Host Controller Interface EHCI compliant host controller is available in Windows XP Service Pack 1 SP1.